Toyota Sienna — Bolt Pattern & Wheel Fitment

The Toyota Sienna bolt pattern is 5x114.3 (5x4.5), a candidate value not yet OEM-verified. Specs by generation below.

Shopping for wheels? Check a new wheel and tire against a stock 2021-2026 Sienna (OEM size pre-filled) →

Toyota Sienna bolt pattern by year

Model years	Bolt pattern	Thread	Lug torque	Status
2021-2026 4th gen (XL40), hybrid-only, TNGA-K	5x114.3 (5x4.5)	M12x1.5	76 lb-ft	Candidate
2011-2020 3rd gen (XL30), incl. 2015 and 2018 updates	5x114.3 (5x4.5)	M12x1.5	76 lb-ft	Candidate
2010 2nd gen (XL20), final model year	5x114.3 (5x4.5)	M12x1.5	76 lb-ft	Candidate

2021-2026 4th gen Sienna bolt pattern 4th gen (XL40), hybrid-only, TNGA-K

Bolt pattern	5x114.3 (5x4.5)
Center bore	60.1 mm
Thread pitch	M12x1.5
Lug torque	76 lb-ft
OEM wheel sizes	17 x 7J, 18 x 7 1/2J, 20 x 7 1/2J, 17 x 4T compact spare (steel on some builds per the MY2024/2025 books)
OEM offset	unverified
OEM tire sizes	P235/65R17 103T, P235/60R18 102V, 235/50R20 100V, T155/80R17 111M (compact spare, if equipped)

Torque note: Toyota prints ONE on-hub torque, 76 ft-lbf (103 N-m, 10.5 kgf-m), for every road wheel and for the 17 x 4T compact spare. In the MY2024 (OM08065U) and MY2025 (OM08070U) books the flat-tire steps cover both 'When replacing an aluminum wheel with an aluminum wheel' and 'When replacing an aluminum wheel with a steel wheel' and then give the single 'Tightening torque: 76 ft-lbf'; so lugTorqueSteel is deliberately absent. The 36.9 ft-lbf (aluminum) / 44.3 ft-lbf (steel) figures in the same chapter are for bolting the STOWED spare into its under-floor carrier ('Stowing the spare tire'), NOT for a wheel on the hub; do not confuse them. Seat-type gotcha: for the alloy wheels the manual says 'turn the wheel nuts until the washers come into contact with the disc wheel', for the steel spare 'until the tapered portion comes into loose contact with the disc wheel seat' - i.e. the factory alloy nuts are washer-type; aftermarket wheels need the nut seat their maker specifies.

Unverified. Candidate values, not yet confirmed by two primary manufacturer sources. Do not rely on them yet: confirm in your owner's manual before buying wheels. How we verify vehicle specs.

Sources (3) — what has been checked so far

Owner's manual Toyota Sienna (XL40 hybrid) Owner's Manual, pub — open document
Full citation and quoted values
Toyota Sienna (XL40 hybrid) Owner's Manual, pub. OM08031U (earliest XL40 book in the OM08 series; page footer 'SIENNA_OM_OM08031U_(U)'; model year not printed in the extracted text, taken as MY2021 because it precedes OM08065U = MY2024). ). Section 8-1 'Tires and wheels', printed pp.525-526 (PDF pp.527-528): 17-inch "Tire size P235/65R17 103T, T155/80R17 111M (spare tire if equipped)" / "Wheel size 17 x 7J, 17 x 4T (spare)" / "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)"; 18-inch "P235/60R18 102V" / "18 x 7 1/2J, 17 x 4T (spare)" / same torque; 20-inch "235/50R20 100V" / "20 x 7 1/2J, 17 x 4T (spare)" / same torque. Flat-tire section 7-2, printed pp.496-498 (PDF pp.498-500): "Have the wheel nuts tightened with a torque wrench to 76 ft•lbf (103 N•m, 10.5 kgf•m)" and "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)".
Owner's manual Toyota 2024 Sienna Owner's Manual, pub. OM08065U (back cover "Printed in the U.S.A. 01-2310-00" = Oct 2023 print,… — open document
Full citation and quoted values
Toyota 2024 Sienna Owner's Manual, pub. OM08065U (back cover "Printed in the U.S.A. 01-2310-00" = Oct 2023 print, MY2024). Downloaded and text-extracted (604 PDF pp.). Section 8-1, printed pp.523-524 (PDF pp.525-526): "Wheel size 17 x 7J, 17 x 4T (spare)", "18 x 7 1/2J, 17 x 4T (spare)", "20 x 7 1/2J, 17 x 4T (spare)", each "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)"; tires "P235/65R17 103T", "P235/60R18 102V", "235/50R20 100V", spare "T155/80R17 111M". Section 7-2, printed p.495 (PDF p.497): "Wheel nut torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)"; printed p.496 (PDF p.498), after both the aluminum-to-aluminum and aluminum-to-steel instructions: "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)". Printed p.499 (PDF p.501), stowing the spare only: "Aluminum wheel: 36.9 ft•lbf (50 N•m, 5.1 kgf•m)" / "Steel wheel: 44.3 ft•lbf (60 N•m, 6.1 kgf•m)".
Owner's manual Toyota 2025 Sienna Owner's Manual, pub. OM08070U (back cover "Printed in the U.S.A. 01-2410-00" = Oct 2024 print,… — open document
Full citation and quoted values
Toyota 2025 Sienna Owner's Manual, pub. OM08070U (back cover "Printed in the U.S.A. 01-2410-00" = Oct 2024 print, MY2025 refresh book, 777 PDF pp.). Downloaded and text-extracted. Section 8-1 'Tires and wheels', printed pp.693-694 (PDF pp.696-697): 17-inch "P235/65R17 103T, T155/80R17 111M (spare tire if equipped)" / "Wheel size 17 x 7J, 17 x 4T (spare)" / "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)"; 18-inch "P235/60R18 102V" / "18 x 7 1/2J, 17 x 4T (spare)"; 20-inch "235/50R20 100V" / "20 x 7 1/2J, 17 x 4T (spare)", same torque each. Section 7-2, printed p.660 (PDF pp.662-663): "Wheel nut torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)" and, after "When replacing an aluminum wheel with a steel wheel...", "Tightening torque : 76 ft•lbf (103 N•m, 10.5 kgf•m)".

Documents are linked at the manufacturer's own site, not re-hosted here; they remain the manufacturer's copyright.

2011-2020 3rd gen Sienna bolt pattern 3rd gen (XL30), incl. 2015 and 2018 updates

Bolt pattern	5x114.3 (5x4.5)
Center bore	60.1 mm
Thread pitch	M12x1.5
Lug torque	76 lb-ft
OEM wheel sizes	17 x 7J, 18 x 7J, 19 x 7J, 17 x 4T compact spare
OEM offset	unverified
OEM tire sizes	P235/60R17 100T, P235/55R18 99V / P235/55RF18 99T run-flat (MY2011-2016), 235/55R18 100V / 235/55RF18 100T run-flat (MY2017-2020), P235/50R19 99V, T155/80R17 101M (compact spare)

Torque note: One torque, 76 ft-lbf (103 N-m, 10.5 kgf-m), printed for every wheel in the spec table INCLUDING the 17 x 4T compact spare (the MY2014-2020 tables give the spare its own 'Wheel size 17 x 4T / Wheel nut torque 76 ft-lbf' block). No separate steel-wheel figure anywhere in the eight XL30 books read, so lugTorqueSteel is absent. Nuts are conical: 'Tighten the wheel nuts until the tapered portion comes into loose contact with the disc wheel seat'.

Unverified. Candidate values, not yet confirmed by two primary manufacturer sources. Do not rely on them yet: confirm in your owner's manual before buying wheels. How we verify vehicle specs.

Sources (4) — what has been checked so far

Owner's manual Toyota 2011 Sienna Owner's Manual, pub. OM45466U (Toyota's downloadableManuals service lists it as 'Toyota 2011 Sienna… — open document
Full citation and quoted values
Toyota 2011 Sienna Owner's Manual, pub. OM45466U (Toyota's downloadableManuals service lists it as 'Toyota 2011 Sienna Owners Manual (OM45466U)'; footer 'SIENNA_U (OM45466U)'). Downloaded and text-extracted (795 PDF pp.). Section 6-1 'Tires and wheels', printed pp.745-746 (PDF pp.747-748): "Tire size P235/60R17 100T, T155/80R17 101M (spare)" / "Wheel size 17 x 7J, 17 x 4T (spare)" / "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)"; "P235/55R18 99V, P235/55RF18 99T, T155/80R17 101M (spare)" / "18 x 7J, 17 x 4T (spare)" / same torque; "P235/50R19 99V" / "19 x 7J, 17 x 4T (spare)" / same torque. Section 5-2 flat tire, printed p.706 (PDF p.708): "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)".
Owner's manual Toyota 2014 Sienna Owner's Manual, pub. OM45483U (listed by Toyota as 'Toyota 2014 Sienna Owner's Manual (OM45483U)').… — open document
Full citation and quoted values
Toyota 2014 Sienna Owner's Manual, pub. OM45483U (listed by Toyota as 'Toyota 2014 Sienna Owner's Manual (OM45483U)'). Downloaded and text-extracted (875 PDF pp.). Section 6-1, printed pp.807-808 (PDF pp.809-810): "Tire size P235/60R17 100T" / "Wheel size 17 x 7J"; "P235/55R18 99V, P235/55RF18 99T" / "18 x 7J"; "P235/50R19 99V" / "19 x 7J"; "T155/80R17 101M" / "17 x 4T"; each block "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)". Section 5-2, printed p.768 (PDF p.770): "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)".
Owner's manual Toyota 2017 Sienna Owner's Manual, pub. OM08007U (listed by Toyota as 'Toyota 2017 Sienna Owner's Manual (OM08007U)';… — open document
Full citation and quoted values
Toyota 2017 Sienna Owner's Manual, pub. OM08007U (listed by Toyota as 'Toyota 2017 Sienna Owner's Manual (OM08007U)'; book date May 6, 2016). Downloaded and text-extracted (676 PDF pp.). Section 9-1, printed pp.606-607 (PDF pp.608-609): "Wheel size 17 x 7J", "Tire size 235/55R18 100V, 235/55RF18 100T" / "Wheel size 18 x 7J", "Tire size P235/50R19 99V" / "Wheel size 19 x 7J", "Tire size T155/80R17 101M" / "Wheel size 17 x 4T", every block "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)". Section 8-2, printed p.580 (PDF p.582): "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)".
Owner's manual Toyota 2020 Sienna Owner's Manual, pub. OM08035U (listed by Toyota as 'Toyota 2020 Sienna Owner's Manual (OM08035U)').… — open document
Full citation and quoted values
Toyota 2020 Sienna Owner's Manual, pub. OM08035U (listed by Toyota as 'Toyota 2020 Sienna Owner's Manual (OM08035U)'). Downloaded and text-extracted (592 PDF pp.). Section 8-1, printed pp.522-524 (PDF pp.526-528): "Tire size P235/60R17 100T" / "Wheel size 17 x 7J"; "235/55R18 100V, 235/55RF18 100T" / "18 x 7J"; "P235/50R19 99V" / "19 x 7J"; "T155/80R17 101M" / "17 x 4T"; each "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)". Section 7-2, printed p.493 (PDF p.497): "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)".

Documents are linked at the manufacturer's own site, not re-hosted here; they remain the manufacturer's copyright.

2010 2nd gen Sienna bolt pattern 2nd gen (XL20), final model year

Bolt pattern	5x114.3 (5x4.5)
Center bore	60.1 mm
Thread pitch	M12x1.5
Lug torque	76 lb-ft
OEM wheel sizes	16 x 6 1/2JJ, 17 x 6 1/2J, 17 x 4T compact spare
OEM offset	unverified
OEM tire sizes	P215/65R16 96T, P225/60R17 98T, T155/80R17 101M (compact spare)

Torque note: One torque, 76 ft-lbf (103 N-m, 10.5 kgf-m). The flat-tire steps cover both 'Replacing a steel wheel with a compact spare tire' and 'Replacing an aluminum wheel with a compact spare tire' and then give the single 'Tightening torque: 76 ft-lbf'; the spec table also prints one 'Wheel nut torque 76 ft-lbf' for all wheel sizes. No separate steel-wheel figure, so lugTorqueSteel is absent even though the XL20 offered 16-inch steel wheels.

Unverified. Candidate values, not yet confirmed by two primary manufacturer sources. Do not rely on them yet: confirm in your owner's manual before buying wheels. How we verify vehicle specs.

Sources (1) — what has been checked so far

Owner's manual Toyota 2010 Sienna Owner's Manual, pub. OM45462U (listed by Toyota's downloadableManuals service as 'Toyota 2010… — open document
Full citation and quoted values
Toyota 2010 Sienna Owner's Manual, pub. OM45462U (listed by Toyota's downloadableManuals service as 'Toyota 2010 Sienna Owners Manual (OM45462U)'; footer 'SIENNA_U_(L/O_0905)'). Downloaded and text-extracted (595 PDF pp.). Section 6-1 'Tires and wheels', printed p.548 (PDF p.550): "Tire size P215/65R16 96T, P225/60R17 98T" / "T155/80R17 101M (compact spare)" / "Wheel size 16 × 6 1/2 JJ (P215/65R16 96T)" / "17 × 6 1/2J (P225/60R17 98T)" / "17 × 4T (compact spare)" / "Wheel nut torque 76 ft•lbf (103 N•m, 10.5 kgf•m)". Section 5-2, printed pp.522-523 (PDF pp.524-525): "Replacing a steel wheel with a compact spare tire", "Replacing an aluminum wheel with a compact spare tire", then "Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m)".

Documents are linked at the manufacturer's own site, not re-hosted here; they remain the manufacturer's copyright.

Toyota Sienna bolt pattern — frequently asked

What is the Toyota Sienna bolt pattern?

5x114.3, which is 5x4.5 in inches, on every Sienna generation in our database (2010–2026).

Do all Sienna model years have the same bolt pattern?

Yes, across 2010–2026: 5x114.3. Years outside 2010–2026 are not in our database and are not covered by this answer.

What is the 4th gen Sienna bolt pattern?

The 2021–2026 Toyota Sienna 4th gen bolt pattern is 5x114.3 (5x4.5), five lugs on a 114.3 mm pitch circle, a candidate value not yet OEM-verified.

What is the 3rd gen Sienna bolt pattern?

The 2011–2020 Toyota Sienna 3rd gen bolt pattern is 5x114.3 (5x4.5), five lugs on a 114.3 mm pitch circle, a candidate value not yet OEM-verified.

What is the 2nd gen Sienna bolt pattern?

The 2010 Toyota Sienna 2nd gen bolt pattern is 5x114.3 (5x4.5), five lugs on a 114.3 mm pitch circle, a candidate value not yet OEM-verified.

Is the Toyota Sienna 5x114.3 pattern the same as 5x4.5?

Yes. 5x114.3 is the metric notation and 5x4.5 the inch notation of the same bolt pattern (114.3 mm ÷ 25.4). Every vehicle on it is listed on the 5x114.3 pattern page.

Will 5x115 (5x4.53) wheels fit a Sienna?

No. The Sienna is 5x114.3; 5x115 is 0.7 mm larger and not interchangeable — the two are so close a tape measure cannot tell them apart, which is exactly why they get mixed up.

Will 5x112 (5x4.41) wheels fit a Sienna?

No. The Sienna is 5x114.3; 5x112 is 2.3 mm smaller and not interchangeable.

Will 5x110 (5x4.33) wheels fit a Sienna?

No. The Sienna is 5x114.3; 5x110 is 4.3 mm smaller and not interchangeable.

Will 5x120 (5x4.72) wheels fit a Sienna?

No. The Sienna is 5x114.3; 5x120 is 5.7 mm larger and not interchangeable.

Which other vehicles use the same 5x114.3 bolt pattern as the Sienna?

In our database: Jeep Wrangler (not yet verified), Toyota Tacoma (not yet verified), Ford Ranger, Ford Mustang, Honda Accord, Ford Explorer (not yet verified), Honda Civic (not yet verified), Honda CR-V (not yet verified), Toyota Camry (not yet verified), Toyota RAV4, Toyota Highlander (not yet verified), Tesla Model 3 (not yet verified), Tesla Model Y (not yet verified), Subaru Outback (not yet verified), Subaru Forester, Nissan Altima (not yet verified), Hyundai Tucson (not yet verified), Nissan Rogue (not yet verified), Subaru Crosstrek (not yet verified), Kia Sportage (not yet verified), Nissan Sentra (not yet verified), Honda HR-V (not yet verified), Hyundai Elantra (not yet verified), Mazda CX-5 (not yet verified). Same pattern is not the same wheel — center bore and stud thread still have to match; see the 5x114.3 pattern page.

What is the lug nut torque for a Toyota Sienna?

2021-2026: 76 lb-ft; 2011-2020: 76 lb-ft; 2010: 76 lb-ft. Use a torque wrench and the manufacturer figure for your exact year; aftermarket wheels may specify their own.

Wheel fitment tools for the Toyota Sienna

Will new wheels fit your Sienna? Compare width, offset and tire size to stock →
All vehicles with a 5x114.3 bolt pattern →
Also 5x114.3: Mazda CX-5 (not yet verified), Jeep Wrangler (not yet verified), Toyota Tacoma (not yet verified), Ford Ranger, Ford Mustang, Honda Accord, Ford Explorer (not yet verified), Honda Civic (not yet verified)
Other Toyota bolt patterns: Tundra, Tacoma, 4Runner, Sequoia, Camry, RAV4, Highlander, Corolla
Bolt pattern finder: look up any other vehicle →
Convert 5x114.3 to inches →
Center bore check: hub-centric ring or not →
Lug nut torque chart →
Tire to rim width calculator: which tire widths fit a wheel →
Wheel spacer calculator: effective offset and stud engagement →
Wheel offset calculator: how far a new offset moves the wheel vs stock →